Fender® Fuzz-Wah Pedal
Set the controls for the heart of the funk! The Fender Fuzz-Wah puts the freak-out at your feet and the fuzz in your beat, all in one rugged, smart-looking pedal. Tilt that baby back and forth for the most groovalicious wah you ever laid ears on; rotate it left to right for fuzz that can easily level large metropolitan areas. Switch each effect on and off and switch the order of the effects for two distinct sounds. Bottom-panel fuzz volume control lets you boost volume or simply match your guitar’s volume when the fuzz is off.


Input Impedance: 1MOhm
Nominal Input Level: –20dBV
Output Impedance: Fuzz —> Wah = 1kOhm; Wah —> Fuzz = 50kOhm
Nominal Output Level: –20dBV
Power Requirements: 9VDC (center pin = negative); 10mA Minimum

Pedal Controls:
• Wah Control—Tilt the pedal back and forth.
• Fuzz Control—Rotate the pedal left and right.
Bottom Panel:
• Effects Order—Switches the order of the effects in the signal path to provide two distinct sounds. Experiment!
• Fuzz Volume—Adjusts the volume level of the Fuzz effect so that you can match the volume level of your guitar when Fuzz is turned off. Also try setting it for a Fuzz effect volume boost!

Features:
• Fuzz Switch—Turns the Fuzz effect on-off.
• Wah—Turns the Wah effect on-off.
• Input Jack—Plug your guitar (or other audio source) in here. Un-plug the input plug from this jack to turn off the device and save power (very important) when not in use.
• Output Jack—Connect to the input of your amplifier (or other audio device).
• 9V Battery—Open the battery compartment on the bottom of the unit by removing the thumb screw. Use alkaline batteries.
• DC Input Jack—Plug in a AC- 9V DC adaptor (Not Included, see specifications) into this jack to eliminate the need for batteries.

Fender® Volume Pedal

A timeless classic. The Fender Volume pedal is a simple, streamlined, silvery sensation that puts sensitive tilt-action volume control at your feet—’cause your hands are too busy! Built-in tuner output comes in handy, too …

Input Impedance: 250kOhm
Output Impedance: 0 to 62kOhm, (Varies with Pedal Position)

Pedal Control: For Volume Control—Tilt the Pedal Back and Forth.

• Tuner Output—Connect to your tuner, if desired. The Volume pedal does NOT affect this output!
• Input jack—Plug your guitar (or other audio source) in here.
• Output jack—Connect to the input of your amplifier (or other audio device).

Fender® Volume-Tone Pedal

Like its elegantly unruly sibling, the Fender Volume pedal, the sleek Fender Volume Tone pedal gives you masterful, Zen-like control over both volume and, um, tone. Tilt this bad boy back and forth to reign supreme o’er the kingdom of volume; swivel it left to right like you mean it to hold infinite sway over the infinite subtleties of tone.

Input Impedance: 150kOhm (250kOhm Volume Pot)
Output impedance: 0 to 62kOhm, (Varies with Pedal Position)

Pedal Controls:
Volume Control—Tilt the Pedal Back and Forth.
Tone Control—Rotare the Pedal Left and Right.

Note: This pedal uses a passive Tone control circuit and works best when connected directly to a passive guitar. If you must use an active guitar or put other pedal before this one, the output impedance of the active device should be 10kOhm minimum for the best performance.

• Tuner Output—Connect to your tuner, if desired. The Volume Control does NOT affect this output, but the Tone Control DOES affect it.
• Input jack—Plug your guitar (or other audio source) in here.
• Output jack—Connect to the input of your amplifier (or other audio device).


출처 : Fender Official Web Site